(New Version) Passleader Free New Update Cisco 350-080 Certification Exam Questions (306-317)
100% Pass Guide: PassLeader now supplying the new version of 350-080 exam vce dumps, we ensure our exam questions are the most complete and authoritative compared with others’, which will ensure your 350-080 exam 100% pass, and now we are offering the free new version VCE Player along with the VCE format braindumps, also the PDF format 350-080 practice tests are available now, welcome to choose.
NEW QUESTION 306
Which switch is not a valid Cisco Nexus 7000 Series model?
A. Cisco Nexus 7000 4-slot switch
B. Cisco Nexus 7000 8-slot switch
C. Cisco Nexus 7000 9-slot switch
D. Cisco Nexus 7000 10-slot switch
E. Cisco Nexus 7000 18-slot switch
NEW QUESTION 307
What is the benefit of the Priority-Based Flow control feature in Data Center Bridging?
A. provides the capability to manage a bursty, single traffic source on a multiprotocol link
B. enables bandwidth management between traffic types for multiprotocol links
C. addresses the problem of sustained congestion by moving corrective action to the network edge
D. allows autoexchange of Ethernet parameters between switches and endpoints
NEW QUESTION 308
Your organization is purchasing Cisco devices as well as non-Cisco devices for switching. Which three statements are correct about connecting Cisco devices to a non-Cisco 802.1Q cloud? (Choose three.)
A. Because Cisco devices transmit BPDUs to the SSTP multicast MAC address on VLANs other than the native VLAN of the trunk, non-Cisco devices do not recognize these frames as BPDUs and flood them on all ports in the corresponding VLAN.
B. Cisco devices connected to the non-Cisco 802.1Q cloud receive these flooded BPDUs. This BPDU reception allows Cisco switches to maintain a per-VLAN spanning tree topology across a cloud of non-Cisco 802.1Q devices.
C. The non-Cisco 802.1Q cloud that separates the Cisco devices is treated as a single broadcast segment between all devices connected to the non-Cisco 802.1Q cloud through 802.1Q trunks.
D. Because Cisco devices transmit BPDUs using the industry standard IEEE 802.1D spanning tree multicast MAC address (01-80-C2-00-00-00), the non-Cisco 802.1Q cloud will seamlessly participate in spanning tree protocol.
E. Only layer 3 connections will work between Cisco devices and non-Cisco 802.1 cloud.
F. Additional equipment will be needed to transmit traffic between Cisco devices and non-Cisco 802.1Q cloud direct connectivity is not possible
NEW QUESTION 309
Which two options describe devices as they operate in FabricPath topologies? (Choose two.)
A. Edge (or leaf) devices: These devices have ports that are connected to classic Ethernet devices (servers, firewalls, router ports, and so on) and ports that are connected to the FabricPath cloud (or FabricPath ports). Edge devices are able to map a MAC address to the destination switch ID.
B. Spine devices: These devices exclusively interconnect edge devices. Spine devices switch exclusively based on the destination switch ID.
C. Edge (or leaf) devices: These devices have ports that are connected to classic Ethernet devices (servers, firewalls, router ports, and so on) and ports that are connected to the FabricPath cloud (or FabricPath ports). Edge devices are able to map a source address to the destination switch ID.
D. Spine devices: These devices exclusively interconnect edge devices. Spine devices switch exclusively based on the source switch ID.
NEW QUESTION 310
Refer to the exhibit. The network topology that is shown in the exhibit has two aggregation switches (SW1 and SW2). The access layer switch connects to both aggregation switches. On SW1 and SW2, ports connecting to the access layer switches are configured as vPC member ports. SW1 and SW2 are also connected using a port channel that is configured as a vPC peer link. Which statement describes the use of the vPC peer-keepalive link in this topology?
A. The peer-keepalive link is used for synchronizing MAC addresses between Agg1 and Agg2.
B. The peer-keepalive link is used for control plane traffic. The peer link is used for the data plane.
C. The peer-keepalive link is used to resolve dual-active scenarios, where the peer link connectivity is lost.
D. The peer-keepalive link is used for the communication of orphaned ports.
NEW QUESTION 311
In a FabricPath topology, each device is identified by a switch ID, and all Layer 2 forwarding tables are built based on the reachability of the switch ID. Which protocol is used to assign the switch ID?
A. No protocol is used. The switch ID is always assigned manually.
B. The Dynamic Resource Allocation Protocol is used to assign the switch ID.
C. The Switch ID Assignment Protocol is used to assign the switch ID.
D. The switch ID is assigned based on the system ID of the device.
NEW QUESTION 312
Which three options describe the interface and direction on which ACL capture can be applied on a Cisco Nexus 7000 switch? (Choose three.)
A. on a VLAN interface
B. in the ingress direction on all interfaces
C. in the ingress direction only on the M2 module
D. in the egress direction on all interfaces
E. in the egress direction on all Layer 3 interfaces
F. in the ingress direction only on M1 module.
NEW QUESTION 313
Refer to the exhibit. During troubleshooting of vPCs, it is observed that virtual port channel 2 is in the down state. Based on the show command output, what is a possible cause of this issue?
A. The virtual port channel is down because LACP is not enabled on the remote switch.
B. The virtual port channel is down because of a VLAN mismatch.
C. The virtual port channel is down because of an MTU mismatch.
D. The virtual port channel is down because of a VLAN and MTU mismatch.
NEW QUESTION 314
Which three options are valid SPAN sources? (Choose three.)
A. VLANs, because when a VLAN is specified as a SPAN source, all supported interfaces in the VLAN are SPAN sources
B. fabric port channels connected to the Cisco Nexus 2000 Series Fabric Extender
C. Layer 2 subinterfaces
D. satellite ports and host interface port channels on the Cisco Nexus 2000 Series Fabric Extender
E. Layer 3 subinterfaces
F. Remote Span Ethernet Ports
NEW QUESTION 315
Which four statements about SNMP implementation on the Cisco Nexus 7000 Series switch are true? (Choose four.)
A. Cisco NX-OS supports one instance of the SNMP per virtual device context.
B. By default, Cisco NX-OS uses the default VDC for SNMP.
C. SNMP supports multiple MIB module instances and maps them to logical network entities.
D. SNMP is VRF aware. You can configure SNMP to use a particular VRF to reach the SNMP notification host receiver.
E. Only SNMP version 3 is supported on NX-OS.
F. Cisco NX-OS supports one instance of the SNMP per switch.
G. Each VDC can have multiple SNMP sessions configured in it.
NEW QUESTION 316
Which three statements about the configuration of vPC+ are true? (Choose three.)
A. The FabricPath switch ID must be configured under the vPC domain.
B. The virtual switch ID of vPC+ must be configured under the FabricPath domain.
C. On the Cisco Nexus 7000 switch, F1 interfaces must be used as the vPC+ peer links.
D. The vPC+ peer link must be configured as a Cisco FabricPath core port.
E. The FabricPath subswitch ID must be configured under the vPC domain.
F. There has to be atleast 4 virtual switches in the FabricPath domain.
NEW QUESTION 317
Refer to the exhibit. Which statement about the interface that is connected to the NPV core switch is true?
A. The switch that connects to the hosts is identified in the design as an NPV edge switch, and the port that connects to the core is an NP port.
B. The interface that is connected to the NPV switch will need to be configured as an N-Port.
C. The interface that is connected to the NPV core will become an FP port.
D. The link between the NPV core switch and edge will come up as an E port.